Roof Replacement Inspection: What to Check at Each Stage
🏠 Renovation🏢 Office Fit-Out🛍 Shop Fit-Out💦 Waterproofing❄ Aircon⚡ Electrical & Plumbing🔨 Carpentry🧹 Deep CleaningGuidesDesign IdeasToolsAbout🔍 SearchFree Quote
🔍 Renovation Inspection

Roof Replacement Works
What to Check Before, During and After

Battens, underlay, flashings and fixings are only visible for a short window while the roof is open. When to look, what to look for, and how to test a new roof before the last payment.

📍 We serve KL, Selangor & Putrajaya.

Roof partly stripped with new timber boards over foil underlay, new grey tiles and old clay tiles

Roof replacement works are best inspected in four passes: before the old roof is stripped, while the frame is exposed, once the new covering is on, and again after the first heavy downpour. Most of what decides whether a new roof leaks, such as battens, underlay, flashings and fixings, is only visible for a short window while the roof is open. For an outside check of your roofer's work, see renovation inspection.

Why a re-roof needs checking while it happens

A re-roof on a terrace, semi-D or bungalow is fast work. A crew strips a section, repairs or replaces what is underneath, and covers it again before the afternoon storm. From the ground, a finished roof looks like a row of neat new tiles or sheets. The parts that keep water out sit under that surface, and nobody sees them again until a ceiling stains.

That is why a roof inspection after handover can only tell you so much. The useful checks are spread across the job, and the owner who plans them before the scaffold goes up gets far more out of each visit.

Read the scope before the first tile comes off

Roof quotations are often a single line: remove old roof, supply and install new roof. That leaves every important decision to the crew on the day. Before work starts, ask for the scope to be written out item by item, so you have something to check against:

ItemWhat the quotation should sayQuestion to ask if it is missing
Roof coveringTile or sheet type, profile and colour by nameWhich exact product is going on?
Battens or purlinsReplaced, treated or reused, and the materialWhat happens if the old ones are rotten?
Underlay or sarkingWhether one goes under the covering, and which kindIs there anything under the tiles at all?
InsulationKept, replaced or addedIs the foil or blanket being put back?
FlashingsParty walls, chimneys, vent pipes, skylights, the valleyNew flashings, or the old ones resealed?
Ridge and hipsBedding and pointing, or dry-fix capsHow is the ridge fixed down?
Gutters and downpipesReplaced or kept, and their outletsWho clears the debris out of them?
Truss or rafter repairsAllowance for repairs found once openWho decides, and how is it priced?

The last row matters most. Rotten battens and termite damage are found only after stripping, and an open roof is a bad place to negotiate. Agree in advance how hidden repairs will be shown to you and approved before they are done.

Before stripping: record the inside and plan the weather

Walk every room under the roof and keep your own dated photo log of existing ceiling stains, cracks and sagging boards. Do the same in the roof space if there is a safe access hatch. Re-roofing shakes the ceiling, drops dust and sometimes puts a foot through a board, and you want to be able to tell new damage from old.

Then ask the roofer how much roof they will open at a time and what covers it when rain comes. In the Klang Valley, afternoon storms arrive quickly. A crew that strips the whole roof on the first day and relies on a few loose tarpaulins is a common source of soaked ceilings and ruined cabinets. Move furniture and electrical items away from the rooms below the open section.

While the frame is exposed

This is the most valuable visit, and it often has to happen at short notice. Ask the roofer to tell you the moment the first section is stripped. With the covering off you can see things that will never be visible again:

  • The trusses or rafters: look for soft, darkened or crumbling timber, termite mud tracks and cracked joints.
  • The battens: new ones should be straight, evenly spaced to suit the tile and fixed at every crossing.
  • Any underlay: laid in the right direction so each strip overlaps the one below, and not torn at the eaves.
  • Insulation: put back or replaced, not left in a heap in the ceiling space.
  • Wiring and pipes in the roof space: not crushed, cut or left hanging where the crew has been walking.

Problems with the frame are not cosmetic. A crack, sagging beam or removed wall that may affect the structure needs a professional engineer's assessment. If trusses need replacing, the guide to timber versus light steel trusses explains why the replacement should come with drawings, and that is worth asking for before the roof is closed.

If you see damaged cables in the roof space, do not touch them. Any repair or change to the electrical installation must be done by an electrical contractor registered with Suruhanjaya Tenaga.

Flashings, valleys and wall junctions

Most new-roof leaks come from the joints, not the field of tiles. On a terrace row, the junction with the neighbour's party wall and the step where your roof meets a higher wall are the usual suspects. While these are being formed, check that each one is a real lapped flashing tucked into the wall, and not a strip of sealant smeared over the gap. The guide to apron, step and counter flashings shows what each joint should look like.

Valleys carry water from two slopes, so they deserve a closer look. A replaced valley should have a clean, open channel with the tiles cut neatly to it, no mortar blocking the flow and no old valley sheet left underneath to rust. The valley flashing guide covers the detail. Vent pipes, skylights and solar brackets are joints too; each needs its own collar or flashing.

The new covering and its fixings

Once a section is covered, check it from a safe vantage point: an upstairs window, a neighbour's balcony or the ground with binoculars. You do not need to climb up, and the guide to staying off the roof explains why you should not.

CoveringWhat to look for from belowWhat it can mean
Clay or concrete tilesCourses running in straight lines, no lifted or cracked tiles, even overlapsA lifted tile lets wind-driven rain under
Metal sheetsScrews in straight rows, sheets lapped the same way, no dents or scratchesScratches rust, and screws off the line miss the purlin
Ridge and hipsA straight ridge line, pointing without gaps, caps fixed downLoose caps are the first thing a storm moves
EavesTiles or sheets overhanging into the gutter, not stopping short of itWater runs behind the gutter onto the fascia

Ask about the screws on a metal roof: they should have sealing washers and be tightened just enough to compress them. Ask also what happens to off-cuts, drill swarf and broken tiles. Metal filings left on a sheet roof leave rust spots within a few wet months.

Gutters, downpipes and the clean-up

Re-roofing fills gutters with broken tile, mortar, nails and old sealant. Before the scaffold comes down, ask for every gutter and outlet to be cleared, and pour a bucket of water into each run to see it flow to the downpipe without ponding. Check the ceiling space for dropped debris and the garden for old roofing that should have been carted away.

If solar panels were taken down for the job, check the reinstalled mounts and the cable entry before anyone leaves; the solar removal and reinstallation guide covers what to confirm.

Testing before the final payment

A dry spell can hide a bad roof for weeks. Before releasing the last payment, ask for a controlled hose test on the riskiest joints: run water above each flashing, valley and skylight in turn while someone watches the ceiling space below with a torch. Then hold back a fair part of the final payment until the roof has been through at least one heavy storm and the ceilings are still dry.

After that first big rain, go round the rooms again with your photo log and compare. A new stain is far easier to raise while the roofer is still expecting the last payment.

Approval, paperwork and your rights

Like-for-like re-tiling is usually treated differently from a change of roof shape or material, but councils and housing schemes set their own rules. If the job changes the roof line, the pitch or the type of covering, check with your council, and on a gated or strata scheme with the management, before work starts.

Collect the roofer's written warranty terms and the product names used, and keep them with your photo log. Under section 53 of the Consumer Protection Act 1999, services supplied to a consumer carry an implied guarantee of reasonable care and skill. Whether it fits your job depends on your contract; check with a lawyer or the Tribunal for Consumer Claims before relying on it.

How ClickBina fits in

Homeowners in KL, Selangor and Putrajaya can book a third-party inspection of your contractor's work; if you want, we can also quote the repairs at the point the roof is open, after it is re-covered, or both. We look at the job against your quotation and the product list, and talk you through each finding before you settle with the roofer.

Sources & references

This page is general guidance, not legal or structural advice. Council rules and your contract decide what applies to your roof.

Want a second pair of eyes on your renovation?

WhatsApp us to book a renovation inspection — we reply within the hour. Third-party inspection of your contractor's work; if you want, we can also quote the repairs. Any visit fee is confirmed with you on WhatsApp before we come. We cover KL, Selangor & Putrajaya.

💬 Book a renovation inspection
Reply within the hourVisit fee confirmed before we comeKL, Selangor & Putrajaya

Common Questions

When is the best time to inspect a roof replacement?
While the old covering is off and the frame, battens and flashings are exposed. That is the only time the parts that stop leaks can be seen. A second look after the new covering is on, and a third after the first heavy rain, complete the picture.
Can I inspect my new roof without climbing on it?
Yes, and you should. Look from upstairs windows, a neighbour's balcony or the ground with binoculars, and from inside the roof space with a torch if there is a safe hatch. Walking on new tiles can crack them.
What should be checked when the old roof is stripped?
The trusses or rafters for rot and termites, the battens for spacing and fixing, any underlay for its laps, and the insulation and services in the roof space. Ask the roofer to call you the moment the first section is opened.
Is a bead of sealant enough at the party wall?
Usually not. A lasting joint relies on a lapped flashing tucked into the wall, with sealant only finishing the top edge. Sealant on its own tends to crack and leak after a few seasons of sun.
How do I test a new roof for leaks?
Ask for a hose test on each flashing, valley and skylight while someone watches the ceiling space below, then wait for a real storm before releasing the final payment. Compare the ceilings with your before-work photo log.
Do I need council approval for a roof replacement?
It depends on the work and on your council. Replacing like with like is often handled differently from changing the roof shape, height or material. Check with your council, and the management on a strata or gated scheme, before work starts.
What if the roofer finds rotten trusses halfway through?
Ask to see the damage before any extra work is agreed, and get the extra priced in writing. A crack, sagging beam or removed wall that may affect the structure needs a professional engineer's assessment.

Book a Renovation Inspection

Tell us what you need — we reply within the hour.

WhatsApp ClickBina← All Guides