Sealer, coats, sheen and clean edges: how to check what your painter delivered against what the quote promised, wall by wall.
📍 We serve KL, Selangor & Putrajaya.

To check a paint job, compare it with the quotation first and the wall second: the named products, the sealer and the number of coats, then the finish under a light held flat against the surface. Most painting defects on a renovation, such as patchy sheen, lap lines, filler showing through and paint on the switches, come from preparation or rushing, not from the paint itself, so they are the painter's to put right. For an outside check of your contractor's work in the Klang Valley, see renovation inspection.
Painting is the last trade on most renovations and the one everyone sees, so it carries the blame for whatever is underneath. A wavy wall, a filled crack that reopens or a damp patch near the floor will all show through even the most careful topcoat. Equally, a painter in a hurry can make a sound wall look poor. Checking the paint job is about separating those two: what the painter did, and what was already there.
It is also the trade where shortcuts are easiest to hide. Nobody can tell from across the room whether a wall had a sealer coat, whether it got the two finish coats the quote promised, or whether the paint was thinned to stretch it. Those choices only show months later as chalking, uneven wear or a colour that scuffs off at the first wipe, by which time the painter has been paid.
A paint job checklist starts on paper. Pull out the quotation and note, room by room, what you were promised. If any of these are missing from the quote, ask for them in writing before the painter starts, because you cannot check against a blank.
| Item in the quote | How you can check it on site |
|---|---|
| Brand and product name for each surface | Read the tins on site before they are opened, and keep one empty tin per product |
| Sealer or primer on new, patched or chalky surfaces | Ask to see the sealer tin and when it went on; it should be on site before the first finish coat |
| Number of finish coats | Agree to be told when each coat is done; a quick look between coats is enough |
| Sheen for each room | Compare a wet area wall and a bedroom wall under the same light |
| Colour codes | Check the code on each tin against your colour schedule |
| Crack filling and skim repairs | Walk the walls with the painter before sealing and agree each patch |
| Protection of floors, fittings and furniture | Look at the floor, switches and window frames before the covers come off |
If you bought the paint yourself on a labour-only job, the same table still applies, but the product questions are yours to answer, and the labour-only versus supply-and-apply guide explains why that shifts the risk. For which first coat suits which surface, see the guide to paint types.
The best time to spot a bad paint job is before any paint goes on. Ask the painter to tell you when the walls are prepared, then spend a few minutes walking them:
A damp patch is the one thing a painter cannot fix. If you see one, pause the painting for that wall and read the guide to a damp wall after renovation before anyone seals it in.
Painting defects hide under flat, overhead light and appear under side light. Use a simple routine on each wall once the paint is dry:
| Defect | What it looks like | Usual cause on a renovation |
|---|---|---|
| Flashing | Dull or shiny patches, often where holes were filled | Filler or skim not sealed before the finish coats |
| Lap lines and roller marks | Bands or stripes across the wall | Stopping halfway along a wall, or too little paint on the roller |
| Poor cover | Old colour or patches showing through | Too few coats, or paint thinned too far |
| Brush marks on trim | Visible strokes on doors and frames | Wrong brush, or recoating before it dried |
| Runs and drips | Teardrops at the bottom of a wall or on a cornice | Paint applied too heavily |
| Wavy cut-in line | Wall colour wandering onto the ceiling | Cutting in by eye in a hurry |
| Bits in the film | Grit, hairs or dust trapped in the paint | Walls not cleaned, or sanding dust in the room |
| Splatter | Dots on floors, glass, fittings and tiles | Floors and fittings not protected |
| Blisters soon after painting | Small bubbles on the surface | Paint over a damp or freshly plastered wall |
Some of these are workmanship and some point to the wall behind the paint. The guide to streaky and uneven paint goes deeper into the causes; at the check, your job is to list each one by room and location so it can be fixed and rechecked.
Ceilings are painted first and checked least, because nobody looks up. Use the torch-flat test on the ceiling too, and look closely around downlights and the aircon unit, where the roller cannot reach evenly. A new plaster ceiling has its own checks for joints and cracks, covered in the plaster ceiling workmanship check.
On doors, frames and skirting, the finish is usually a harder enamel or a water-based trim paint. Run a finger along the edge of a door: it should feel smooth, with no sags along the bottom edge. Check that door hinges, latches and handles are clean rather than painted over, and that the doors still close without sticking against fresh paint.
Outside walls and bathrooms are where the wrong product does the most damage, because the failure comes from weather and steam rather than from wear. On an exterior job, check that the products on the tins are the weatherproof system named in the quote, that cracks in the render were sealed before painting, and that the scaffold or ladder points were made good afterwards. Exterior repainting has its own sequence, covered in the exterior repainting process guide.
In a bathroom or wet kitchen, ask which paint went on the walls and the ceiling. A standard emulsion in a shower room will mark and grow mould far sooner than an anti-mould or bathroom grade. If the quote named one and the tins show another, raise it before the final payment, not after the first patch of black spots appears.
Many disputes about paint are really about a purpose nobody wrote down: a washable wall in a child's room, a rain-facing gable, a kitchen wall behind the hob. Under the Consumer Protection Act 1999, section 54 implies a guarantee that a service, and what it produces, will be reasonably fit for a particular purpose the consumer makes known to the supplier before or when the contract is made.
Section 54(2) also says that guarantee does not apply where the consumer does not rely, or cannot reasonably rely, on the supplier's skill or judgment. On a labour-only job where you picked the paint yourself, that may matter. The practical lesson is simple: write the purpose of each surface into the quote. How the Act applies to your own job depends on your contract; check with the Tribunal for Consumer Claims or a lawyer before relying on it.
If you are still choosing a painter for the next job, the guide to hiring a painting contractor covers the quote and payment side.
Homeowners in KL, Selangor and Putrajaya can ask us for a third-party inspection of your contractor's work; if you want, we can also quote the repairs. We walk the painted rooms against your quotation and colour schedule, room by room, and we go through what we found with you before you decide what to do. For a house newly handed over by a developer, the new-home defect inspection page applies instead.
This page is general guidance, not legal advice. Your rights depend on your contract and the facts of the job.
WhatsApp us to book a renovation inspection — we reply within the hour. Third-party inspection of your contractor's work; if you want, we can also quote the repairs. Any visit fee is confirmed with you on WhatsApp before we come. We cover KL, Selangor & Putrajaya.
💬 Book a renovation inspectionTell us what you need — we reply within the hour.