Acrylic Sealant vs Silicone: Which Joint Gets Which?
🏠 Renovation🏢 Office Fit-Out🛍 Shop Fit-Out💦 Waterproofing❄ Aircon⚡ Electrical & Plumbing🔨 Carpentry🧹 Deep CleaningGuidesDesign IdeasToolsAbout🔍 SearchFree Quote
🖌️ Painting

Acrylic Sealant vs Silicone
Which One for Which Interior Joint (2026)

Paint peeling off a sealant line, or a joint cracking again? The answer is usually the wrong tube in the wrong joint.

📍 We serve KL, Selangor & Putrajaya.

Gloved hands running a white sealant bead along the joint between a window frame and a plaster cornice

Use acrylic sealant for dry interior joints that will be painted: gaps along cornices, skirting, door and window frames and fine plaster cracks. Use silicone for joints that get wet or must stay flexible: around showers, baths, basins, sinks and worktops, and on glass. Acrylic can be painted over and cleans up with water, but it moves little and is not made for joints that sit in water. Silicone stays flexible and resists water, but paint will not stick to it and almost nothing bonds to its residue. Get the choice wrong and you either have peeling paint or a joint that cracks within months.

Two different jobs, two different tubes

Both come in the same cartridge, both go in the same gun, and both are sold as sealant or caulk at the hardware shop. They are built for different jobs.

  • Acrylic sealant (often called painter's caulk or gap filler) is a water-based paste. It dries to a firm, slightly flexible line that takes paint. It is a finishing material: it closes the small gaps that would otherwise show as dark lines after painting.
  • Silicone sealant cures to a rubbery bead that stays flexible and sheds water. It is a sealing material: it closes junctions between materials that move independently and get wet, such as a shower screen and a tiled kerb.

ClickBina's polyurethane vs silicone guide covers the outdoor side: facade, window and roof joints. This page is about joints inside the house.

Acrylic vs silicone at a glance

PropertyAcrylic sealantSilicone sealant
Can it be painted?Yes, once a skin has formed (check the label)No: paint beads and peels off it
Water resistance once curedFine for splashes; not for joints that sit wetMade for wet joints
MovementLow: for cracks and joints that hardly moveHigh: stays flexible
Clean-up while wetWaterSolvent or wipes; it smears
Sanding and smoothingSome products can be sanded once curedCannot be sanded
Mould resistanceNot its jobSanitary grades carry a fungicide
Removing it laterCuts and scrapes out; can be painted overMust be cut out completely; residue blocks new sealant and paint
Typical placesCornice, skirting, door frames, plaster gapsShower, bath, basin, sink, worktop, glass

Where acrylic sealant belongs

The manufacturer data sheets are clear about the job. Sika describes its Sikacryl-150 as a professional acrylic sealant for painters, for indoor connection joints with low movement in plaster, concrete, brick, board and wood, and for interior crack filling, as long as the cracks are not under permanent water immersion. In practice that means:

  • the line where a cornice or ceiling meets the wall;
  • the gap along the top of skirting boards;
  • around timber door frames and architraves, and the inside edge of window frames;
  • where a gypsum board partition or ceiling meets brick or concrete;
  • fine, non-moving plaster cracks before painting;
  • around pipes and cables where they come through a wall that will be painted.

These are the gaps that show as thin shadows after a repaint. Sealing them before the last coat is a normal part of painting preparation.

Where silicone belongs

Silicone is the choice wherever water sits on or runs over the joint, or where two different materials move against each other: the junction of a shower tray or kerb with the wall, the edge of a bath, the line between a basin or sink and the worktop, the back edge of a kitchen worktop against tiles, and glass in frames.

For bathrooms the right product is a sanitary-grade silicone, which contains a fungicide so the bead resists mould. ClickBina's silicone resealing guide explains the difference between acetoxy-cure silicone, which smells of vinegar, and neutral-cure types, and why the cheap general-purpose tube is a false economy in a shower.

The painting rule that decides most cases

If the joint will be painted, it is not a silicone joint. Ordinary paint does not stick to ordinary silicone: it beads while wet and flakes once dry, leaving a permanent shiny line in a matt wall. Once silicone has been used, the old bead and its thin residue film must be cut and cleaned off before anything else will hold.

Acrylic is the opposite. SikaSeal Acrylic, for example, is stated as able to be painted over using water-based paints. Always check the label for when paint can go on, and test a small area if you are using an unusual paint.

Cracks that keep coming back

Acrylic moves very little. The Sikacryl-150 data sheet gives a movement capability of ± 10% and limits it to cracks and non-movement joints, and SikaSeal Acrylic declares ± 5%. That is enough for a settled hairline crack or a cornice gap. It is not enough for a joint that opens and closes every day.

A crack that returns along the same line after every repaint is usually a joint between two materials, for example where brick meets a concrete column. ClickBina's guide to cracks between brick and columns explains why those are cut out and filled with a flexible sealant or bridged with mesh, and the gypsum partition crack guide covers board joints. A wide, growing or stepped crack is a different matter and should be looked at before anything is filled.

Grey areas: kitchens, window sills and skirting near wet floors

  • Wet kitchen backsplash and sink edge. Silicone, because water sits on it.
  • Painted wall above a worktop. Silicone along the worktop line, then paint stops at the tile or backsplash edge rather than running over the bead.
  • Inside window sill. Acrylic where the sill meets painted plaster; silicone where it meets the glass or frame and condensation runs.
  • Skirting in a bathroom or by a wet floor. Silicone or a joint made for wet areas; SikaSeal Acrylic is listed as unsuitable for permanently flexible sealing and for places where wet conditions exist.
  • Gaps wider than a pencil line. Many acrylics are made only for small gaps; SikaSeal Acrylic says it is not intended for gaps, joints or voids larger than 5mm wide or deep. Fill or back wider gaps first.

How a good acrylic or silicone joint is made

  1. Remove the old sealant completely. Over old silicone, cut it out and clean the residue film off both faces.
  2. Make sure the joint is clean, dry and sound; scrape out loose plaster and dust.
  3. For wide gaps, push in a backing rod or fill first, so the sealant forms a bead rather than a plug.
  4. Mask both edges with tape for a straight line.
  5. Gun the sealant in one steady pass and tool it smooth with a wet finger or tool.
  6. Pull the tape while the sealant is still wet.
  7. Let acrylic skin over before painting, and keep water off silicone until it has cured as the label says.

Most failed joints fail at step one. A fresh line run over an old, mouldy or cracked bead looks right for a fortnight and then lifts in one piece.

What sealant work costs

Sealant is rarely priced on its own: it is part of painting preparation or of resealing a wet area. These figures are published on ClickBina's guides (indicative 2026, Klang Valley):

ItemIndicative priceSource guide
Re-siliconing, rental handover contextRM150 – RM300Silicone resealing guide
Re-grouting, rental handover contextRM200 – RM600Silicone resealing guide
Extra prep before painting: crack filling, skim and sandingRM0.50 – RM2 per sq ftCeiling hole patching guide
Walls and ceiling repaint, minor crack fillingRM3.00 – RM4.50 per sq ftCeiling hole patching guide

Want this priced for your home?

WhatsApp us your job details for a quote — we reply within the hour. A renovation site visit is free, and a repair inspection is RM180, deducted from the bill if you go ahead. We serve KL, Selangor & Putrajaya.

💬 WhatsApp for a quote
Reply within the hourFlat price, no hidden chargesExperienced KL & Selangor contractor

When comparing quotes for painting, check whether sealing gaps at cornices, skirting and frames is included in the preparation, and for a reseal, whether the old silicone is cut out completely rather than covered.

How ClickBina can help

Painting is one of ClickBina's own trades. See ClickBina painting services for what a repaint covers. ClickBina is an experienced KL & Selangor contractor for whole-house refurbishment and trade coordination, so a reseal around the shower and a repaint can be planned together.

WhatsApp us your job details for a quote: where the joints are, roughly how many metres, and whether the area will be painted. We reply within the hour, and the price we agree is a flat price with no hidden charges.

Sources & methodology

  • Sika, Sikacryl-150 product data sheet — indoor low-movement joints, over-paintable, movement capability, interior crack filling not under permanent water immersion.
  • Sika, SikaSeal Acrylic product data sheet — interior use, water-based paints, movement capability, limits on wet areas and gap size.
  • ClickBina silicone resealing guide — sanitary grade, cure types, removing old silicone; re-siliconing and re-grouting prices.
  • ClickBina ceiling hole patching guide — painting preparation and repaint rates.
  • ClickBina polyurethane vs silicone guide — exterior joints and paintability.

How we estimated prices: every RM figure on this page is quoted unchanged from the ClickBina guide named in the table; they are indicative Klang Valley ranges for 2026, not fixed rates. Product properties are taken from the manufacturer data sheets named above; other brands differ, so read the label.

Ready to get it sorted?

WhatsApp us your job details for a quote — we reply within the hour. A renovation site visit is free, and a repair inspection is RM180, deducted from the bill if you go ahead. We serve KL, Selangor & Putrajaya.

💬 WhatsApp for a quote
Reply within the hourFlat price, no hidden chargesExperienced KL & Selangor contractor

Common Questions

Can you paint over acrylic sealant?
Yes. Acrylic sealant is made to be painted, usually with water-based paint once a skin has formed. Check the label and test unusual paints.
Can you paint over silicone?
No. Paint beads and peels off ordinary silicone. If a joint will be painted, use acrylic, or cut the silicone out completely first.
Is acrylic sealant waterproof?
It copes with splashes once cured, but it is not made for joints that sit in water. Use silicone around showers, baths and sinks.
Which sealant is best for cornice and skirting gaps?
Acrylic sealant, because those joints are dry, barely move and are normally painted.
Why does my acrylic-filled crack keep coming back?
Acrylic moves very little. A crack that reopens on the same line is usually a moving joint and needs a flexible sealant or mesh.
Can I put new silicone over old silicone?
No. The old bead and its residue must be cut out and cleaned off, or the new bead lifts.
Is acrylic the same as painter's caulk?
Yes, in everyday use. Painter's caulk and gap filler are usually acrylic sealants made for dry, paintable joints.

Free Quote

Tell us what you need — we reply within the hour.

WhatsApp ClickBina← All Guides
💬 Get Your Free Quote